For many home Internet users from the Rostelecom provider, there are various problems with connecting to the network. Often such problems occur due to improper installation of equipment. From this article you will learn how to configure a router Intercross under home Internet from Rostelecom.
First of all, it is necessary to deal with what Wi-Fi router can be used to connect to the Internet from Rostelecom. The official website of the represented provider has the following list of recommended equipment:
- Intercross ICXDSL 5633 NE-02;
- Sagem Fast 2804;
- NEC Xavi 825;
- D-Link.
After you have chosen necessary equipment and purchased it, you can start physical connection Router. Performed this procedure in the following way:
- First of all, select a place where Wi-Fi router will be located. When choosing a place, consider the range of the signal.
- After selecting the place, stretch the Internet cable to the router.
- Connect the cable in the connector on which the inscription "LINE".
- Connect the cable from the router to the connector with the "Phone" inscription.
- DSL connector connect the cable with a connector that is located on the splitter and is called "Modern".
Login to settings
After installing the router to the computer, you must properly set the connection parameters. To do this, the user needs to get into the appropriate section. This can be done as follows:
- All intercross modems have the defaultIP address - 192.168.1.1. Therefore, you need to set the subnet address 192.168.1.0 on the computer, and in the Gateway sectionIP address modem (indicated above).
- After that, open any browser installed on your computer.
- In the address bar, enter the IP address of the modem.
- The authorization window opens.
- In the Login and password fields, enter the "Admin" (without quotes).
So you can go to the settings section Wi-Fi Router Intercross. On how to configure the router to connect to the Internet from Rostelecom, read below.
Appearance and interface
After authorization in the Router window Intercross, the user will get to the main page on which you can find out the following information: DSL connection status, the current network connection speed, connection time. The following sections will be presented in the router window, which will be needed to configure the router:
- Status. Main page.opening immediately after authorization. This indicates all information about the connection.
- Wizard. Opening this section, you can change the basic parameters of the router.
- LAN. Here are the information of the local computing network.
- WAN. Global is configured here computer network.
- ADVance. The following parameters of the DNS servers are installed.
- Admin. This section allows you to install new password To enter the system for setting the router Intercross.
- Diagnostic. The latest available section in which the system is diagnosed.
Modem Setup Intercross for Rostelecom - Instructions
By connecting the router to the computer and, sorting out with the intercross router interface, you can start setting.
Setting the router Intercross:
- First you need to open the router settings window. To do this, start any browser and in the search bar, enter the following request - 192.168.1.1.
- The authorization window opens.
- In the Login and Password fields, specify "admin" (without quotes).
- Once in the main settings menu, go to the "Wizard" or "Advanced Setup" section (depending on the version of your router).
- Delete the factory settings by clicking on the "Remove" button.
- Now add your own settings by clicking on the "Add" button.
- Specify the IP address and DNS server (this information is provided in the contract you entered into when connected).
- In VPI, set the value - 0.
- In the VCI item, set the value - 35.
- In the Service Category paragraph, specify "UBR WITHOUT PCR".
- Select the PPP Over Ethernet PPPOE connection type.
- In the Encapsulation Mode section, specify "llc / snap-bridging".
- Next, enter the login and password from your contract.
- Check the ticks in the items: Enable Nat, Enable Firewall, Enable Wan Service.
- Specify the connection name (you can enter any name).
- Check out all settings.
- If everything is correct, then press "SAVE".
After performing all the actions specified above, you can successfully configure the Internet connection through the Intercross router. If you have any problems when connected, then, first of all, repeat the connection procedure. If difficulties arose, then ask Rostelecom employees, how to configure the intercross modem.
Video "Setting up an intercross modem in PPPoE mode"
Open the browser (Internet Explorer, Opera, Firefox or any other), in the address bar, type 192.168.1.1, enter the username - Admin, password - admin. After that, the page shown in Figure 1 should be booting.
Figure 2.
On the left side of the page, click on the inscription DHCP, then you need to install DHCP None in the DHCP MODE parameter, then click on the Apply Changes button. The page, should look like in Figure 3.
Figure 3.
After that, the main inscriptions will appear at the bottom of the page and the SAVE button on which should be pressed. The page will change (the red inscription will disappear) and it will be like Figure 4.
Figure 4.
Figure 5.
At the bottom of the page in the table in the SELECT patch you need to put the point. After that, you should change the parameters to the following: VPI - 8, VCI - 81, Encapsulation - LLC, Channel Mode - 1483 BridgeD, the page must change and look like in Figure 6.
Figure 6.
Then press the MODIFY button, the page must change as in Figure 7.
Figure 7.
After that, the red inscription appears from the bottom with the Save button to which you should click. After these actions, close the page and press the power key on the modem, wait 5 seconds and turn on the modem. Next, create a VPN connection.
If you want to change the Internet connection settings, produce the proposed
setting, having done the following steps:
Step 1
Connect the connection to local network and define the TCP / IP Protocol properties for
this connection: Get the IP address automatically. Get the address of the DNS server automatically.
Step 2.
Turn on the power of the router, the POWER indicator should light up. Make sure the computer
connected to the 1st port of the modem (LAN 1), while the LAN 1 light should be burned.
Step 3.
On a computer, call a browser (for example, Internet Explorer.) And in the address bar, type the address: http://192.168.1.1. A page appears on which you need to enter authentication data to enter the user interface. For this router, they matter: User Admin, Admin Password. To log in, click the "Login" button.
After downloading, a window will appear:
This window displays information about the device.
Step 4.
In the left column, select "Advanced Setup → Layer2 Interface → ATM Interface", the following page will appear.
IN software The modem has already recorded a login and password for using the services of MGTS OJSC, corresponding to the authentication data of the envelope invested in the package. When you return the factory modem settings, data for using the services of MGTS OJSC (login and password) will correspond to the authentication data of the envelope invested in the package.
If you want to change the username or password, in the left column, select "Advanced Setup → Wan Service" and press the "Edit" button in the right column of the table. A window will appear in which you can enter the username and password.
Physical connection
Connect the telephone cord coming from the station to the connector " Line»Splitter, telephone Connect to the connector " Phone", And the connector" DSL"On the modem - to the connector" Modem.»Splitter.
Primary setting of OS.
By default, the Intercross ICXDSL 5633 NE-02 has an IP address 192.168.1.1 with mask 255.255.255.0 . Therefore, for the primary setting, you will need to assign an IP address from the 192.168.1.x network on the network card. After setting up the network card, connect the modem to it and check the availability of the modem using the Ping command 192.168.1.1. If the modem is still unavailable, follow the procedure for resetting the settings described in the instructions for the modem.
In TCP / IP protocol settings network cards Computers that will be connected via intercoard ICXDSL 5633 NE-02 to the Internet, enter an IP address assigned to the modem on Ethernet as the DNS server addresses of the provider DNS server addresses.
After performing the primary settings of the network board and check the availability of the modem (Ping 192.168.1.1), start the Internet browser and type in the address bar 192.168.1.1 . At the request of the user name, enter " admin.", Enter the default password for the password -" admin." If the password is not suitable, follow the procedure for resetting the settings described in the instructions for the modem (from the back of the modem there is a recessed button. It must be pressed and hold the seconds 20-30).
Modem Setup in Router Mode
After entering, click on the point Setup.
On the left click New Connection
1. Type the connection name (for example, inet)
2. Remove the checkbox with Firewall
3. Fill login with password (issued by the provider)
4. Fill out the VPI and VCI fields (clarify the provider)
5. Press the Apply button (Apply settings)
Press the Save All button (Saving settings)
Setting completed
Configure Wi-Fi in Modem
Separate BRIDGE connection in a separate LAN-group
There, then you can transfer one ethernet port so that IPTV go through it
Top Housing Wireless.
Left Setup.
Should be tick Enable AP.
Primary ssid: Title_Seti_set (any name in English)
Zhmem. Apply
Click on the left Security
1. Select encryption mode WPA
2. You can choose and WPA2.but if it supports it your Wi-Fi network card
3. Select Pre-Shared Key and B. Psk String Drive Password (10 characters)
4. Zhmem. RESTART ACCESS POINT.
In the window that appears, click on the button RESTART ACCESS POINT.
the configurations on the computer will be described later.